The looks of the lamps inspire when they glow. Of course, you didn’t set a lamp on the nightstand to stand tall as a showpiece. But what if one has gone into dormancy and you don’t know how to fix a lamp? Don’t worry; we have your back.
We know you want your lamp to be working and charming all before your guest arrives. So, here we have listed the simplest methods to help you get through this.
Knowing the history of your lamp’s problem is quite necessary to make it working again. That’s why we have also crafted an analysis for each problem. Before you disassemble each of its parts, first check out where the problem is originated from.
Also Check: 9 Best Table Lamps that fits everyone’s Bill
4 Possible Issues of a Lamp and Their Quick Fixes
Several parts make or break a lamp. Like, if your lamp isn’t working, that doesn’t mean every part has collapsed all at once. In most cases, the problem is just in a specific part—all you have to arrest it.
Here, we’ll tell you how to examine each lamp’s part to check if that needs amendments.
Problem # 01: Dead Bulb
No one talks of the obvious, i.e., bulb issue. Agreed that your LED bulb was supposed to live for years to come, but it can fail. Before unscrewing your lamp as a whole, make sure to initiate checking from here.
Analysis
Deem down and check if your bulb is properly fitted into the socket to glow. If that’s not the matter, bring another working bulb you have in your home. Tighten that bulb and plug the lamp into the outlet to observe the results.
Solution
Congratulations if the new bulb worked out. If not, get another bulb from the market or home store. Well, you got a chance to have a new bulb type, shape, and color this time. So, good luck!
Problem # 02: Cord Breakdown
One measure in a non-responding lamp is the cord. Possibilities are that your naughty pet has made it fall apart. Or, the tangled wire has itself turned you down. The poor age of the cord could also be a cause, by the way.
Analysis
Follow the wire from the stem of your lamp to the plug. Check out if there’s crack or wear at any point. If that’s the case, it’ll be apparent. All you have to do now is follow the further guidance.
Solution
The simplest thing you can do to get the lamp back to life is the replacement of wire. To replace it, bring a new wire and follow these steps:
- Remove the socket of the lamp
- Detach the threaded wire from the socket with the help of a screwdriver
- Remove the bottom covering of the lamp gently
- Pull out the detached cord from the bottom
- Insert the new cord from the bottom
- Push it upwards till it reaches the other end
- Split the two mouths of the wire a bit
- Tie a knot between them to prevent backward movement
- Take the rim of the wire and attach it to a screw on either side of the socket
- Put the switch cover back on… and VIOLA!
Problem # 03: Unwell Socket
Being so much concerned about your bulb’s falling can also make you land into a lamp problem. By that, we mean you might have tried to tighten your bulb a lot. This could be the reason your sockets have gone bad.
Analysis
Knowing about the faulty socket would require you a working bulb. Snap-in the bulb into the socket and give it fewer turns. If that works out, you are safe from more steps. If not, below are the steps you should follow next.
Solution
Sockets are easy to replace. All you need is careful handling and step by step know-how, and there you go with it:
- Separate the socket shell from the socket cap by squeezing
- Pull it a bit upward while squeezing
- Unscrew the wires on either side of the socket with a screwdriver
- Introduce a new socket to the socket cap
- Rewire the threaded/stranded wire in the loop form around the screws
- Tighten screw afterward
- Put the socket back in the lamp
- Place the bulb, shade, and harp you’ve removed earlier
Problem # 04: Disintegrated Plug
Often, your plug is also the hidden cause behind your non-working lamp. As plugs have a low melting point, a change in voltage at your home has probably knocked it down.
Analysis
To know if the problem maker is your plug, look carefully at it. Check if both the prongs of your plug are straight and go well in the outlet. Also, deem down with the casing. If the plastic is scratched or melted, understand that plug demands replacement.
Solution
To overcome the issues with your plug, replace it. These steps are to be followed in the process of changing the plug:
- Use a plier and separate the wire from the plug
- Substitute the new plug with the old
- To get it plugged, take the cord of your lamp in your hand
- Split the wires into two for a few inches
- With the help of a wire stripper, get the coating off from each wire for about 3 inches
- Twist the wire clockwise that has popped up on stripping
- On the other hand, unscrew the back cover of the new plug with a screwdriver
- Separate the prongs after unscrewing
- Keep the screw safely on one side
- Take the twisted wires in hand and pass them through the hole at the back of the plug
- Pull them upward from the front hole of the plug
- Screw up the silver screw and wrap the wire around
- Fasten the wire underneath with the screwdriver
- Bring back the plastic cover of the plug and cover the wire
- Attach the prongs with the screw you unscrewed before
Final Thoughts
These were the four major problems that can knock your lamp down and make it unworthy. However, they aren’t incurable or hassle to deal with. You can handle these tiny issues yourself at home.
Hope that now you aren’t still figuring out how to fix a lamp. This guide is because packed with every minute detail on the topic. So, do let us know, did these tricks and methods work out for you?
2 thoughts on “How to Fix a Lamp Yourself in No Time? | 4 Possible Issues”